- Are old stereo speakers worth anything?
- How long should you break in a subwoofer?
- Does an amplifier need to warm up?
- Do speakers get better with age?
- Do preamp tubes need to warm up?
- How do I know if my speakers are damaged?
- Do speakers go bad if not used?
- Do speakers wear out?
- How do you break in monitor speakers?
- Do speakers need to break in?
- How do you break in speakers fast?
- Can you damage speakers by playing them too loud?
- How long should you break in speakers?
- How long do speakers usually last?
- Should I let my tube amp warm up?
- Do solid state amps need to warm up?
- How do I know if I blew my speakers?
- Do speakers sound better after break in?
- How do I stop my speakers from blowing?
- Do subwoofers get louder as they break in?
- What makes a speaker go bad?
Are old stereo speakers worth anything?
If you’re interested in selling your old stereo equipment, remember, they aren’t all worth lots of money.
As a general rule, most transistorized equipment — mainly receivers from the 70’s and 80’s — are not worth as much as you’d like them to be..
How long should you break in a subwoofer?
How long should a break-in period last? Some speaker manufacturers will recommend a break-in period of around 10 hours. That should be plenty of time to allow your subwoofer to get settled in, if you decide to do this at all.
Does an amplifier need to warm up?
no. Tube amps have to warm up because the tubes have heaters in them that have to heat the cathodes up to the point where they glow red, and emit electrons using a process known as “Thermionic Emission.” Transistors work differently, and so are pretty much “instant on” devices.
Do speakers get better with age?
And the foam surround will rot away with time. So, generally speaking, given enough time or “age” your speakers will not get better. They will, if not taken care properly, and if not serviced from time to time, eventually reach the end of their “life cycle”.
Do preamp tubes need to warm up?
A tube preamp (not power amp, just the preamp) should not have to be warmed up beyond the 15 to 30 seconds needed for the filaments to arrive at temperature.
How do I know if my speakers are damaged?
Step 1: Disconnect the speaker. Remove the wires from the audio system, and with them still attached to the speaker, attach them to a 9-volt battery. You may hear a popping sound coming from the speaker. This means the speaker is working. If there is no sound, that indicates the speaker is blown.
Do speakers go bad if not used?
It depends on the previous owner and how they used the speakers. If speakers are taken care of properly they can literally sound better than when they were new. However, 9 out of 10 times they end up sounding worse, so yes they can go bad.
Do speakers wear out?
Yes, everything wears out. In the case of a loudspeaker, the magnetic field will reduce in time,and the suspension sags. Some speakers using a foam rubber seal ,have the foam just collapse .
How do you break in monitor speakers?
A: Breaking in your speakers simply means loosening up the driver surrounds and evening out the frequency response of the speakers by playing audio through the speakers. The easiest way to this is to play a CD on repeat through the speakers at a medium- to medium-soft volume for a few days at night.
Do speakers need to break in?
After about 100 hours of use, your speakers should be broken in. The speaker surround and spider materials loosen up the more the speaker is used. Not all speakers will sound dramatically different after break-in. Some improve only marginally, while others can change dramatically.
How do you break in speakers fast?
Before breaking it in it’s advisable to warm up the speaker gently for a few minutes with low-level playing or background hum. Break in a speaker with a fat, clean tone: turn up the power amp volume to full, and control the level with the preamp gain.
Can you damage speakers by playing them too loud?
The answer is yes, you can play music too loud and damage your speakers. There are a couple ways this mishap on your part can occur too which you should familiarize yourself with. When you over-power low-frequency speakers or subwoofers, it’s either electrical or mechanical in nature.
How long should you break in speakers?
20-30 hoursThe most basic way to run in your speakers is to set them up with your system and use them normally. Usually the speakers will be sufficiently run in after a total of 20-30 hours of normal use and they will often continue to develop and improve for the first hundred or so hours.
How long do speakers usually last?
roughly 1-3 yearsIn my assessment and experience a mid-range set of speakers should last roughly 1-3 years, with moderate use. Higher-end speakers should last anywhere from 3+ years to an indefinite amount of time, again depending upon how they are used and how they are cared for.
Should I let my tube amp warm up?
It is important, too, that the warmup that you give your tube amp is very thorough. If they are not warmed up properly, the tone of your playing will not be as good as it ought to be. As a rule of thumb, your tube amp needs to be warmed up for 20 to 30 minutes at least before you can start playing your guitar.
Do solid state amps need to warm up?
Yes, solid state amps take time to warm up… sometimes they get better over days — one of the reasons i never bother turning my amps off.
How do I know if I blew my speakers?
The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce. Or there could be no sound at all.
Do speakers sound better after break in?
The good news is your speakers will absolutely sound better after the initial break in period. … However, to break your speakers in well, you’ll want to play something with large dynamic range, something with solid deep bass, as well as something with strong high end.
How do I stop my speakers from blowing?
Keep the volume on your receiver at least 5-6dB below its max setting. The volume adjustment on most receivers goes from -80dB (mute) to about +16dB (max). By staying below -6dB below that max setting you can typically avoid over-driving the receiver, which could potentially damage your speakers and receiver.
Do subwoofers get louder as they break in?
No, that’s normal, especially subs with stiff suspensions. Once they loosen up, they will play louder and sound better.
What makes a speaker go bad?
Failures in tweeters, midrange and midbass speakers are caused by ELECTRICAL and/or MECHANICAL power handling issues. Most failures occur from ELECTRICAL failure caused by applying too much power to the speaker’s voice coil. … MECHANICAL failures occur by using the wrong crossover point for the speaker.